NRF24L01 2.4GHz Wireless Transceiver
75.00 EGP
2.4GHz ISM band transceiver, ultra-low-power wireless applications. Features 2Mbps speed and Enhanced ShockBurst.
| Weight | 0.02 kg |
|---|---|
| Dimensions | 2.9 × 1.5 × 2 cm |
1 in stock
NRF24L01+ Wireless Module
This wireless transceiver module is based on the Nordic Semiconductor nRF24L01+ single-chip 2.4GHz transceiver. It is designed for ultra-low-power (ULP) wireless applications operating in the worldwide 2.4GHz ISM frequency band. As a module featuring a Power Amplifier (PA), Low-Noise Amplifier (LNA), it is engineered for long-range communication.
Features
- Operating Band: Worldwide 2.4GHz ISM band operation.
- Data Rates: 250kbps, 1Mbps, and 2Mbps.
- Ultra-Low Power: Designed for ULP operation with 900nA power-down and 26µA standby-I modes.
- Enhanced ShockBurst: On-chip baseband protocol engine provides automatic packet handling, automatic packet transaction handling, and auto-acknowledgment.
- MultiCeiver: Features 6 parallel data pipes for 1:6 star network configurations.
- Low-Cost BOM: Requires only a low-cost ±60ppm 16MHz crystal.
- Dimensions: 48×15.5x14mm
- Antenna length: 108mm
Specifications
| Specification | Details |
|---|---|
| Frequency Band | 2.400 – 2.4835GHz |
| RF Channels | 126 RF channels |
| Modulation | GFSK |
| Air Data Rates | 250kbps, 1Mbps, 2Mbps |
| Supply Voltage | 1.9 to 3.6V |
| Power Consumption (Core Chip) |
|
| Receiver Sensitivity (Core Chip) |
|
| Payload Length | 1 to 32 bytes, dynamic |
| FIFO | 3 separate 32-byte TX and RX FIFOs |
Pinout
Applications
- Wireless Data Transmission
- Remote Control Systems
- Wireless Networking
Package Content
- 1x NRF24L01 Wireless Module
Related products
WeMos D1 ESP8266 WiFi Board (UNO Based)
The ESP8266 D1 R1 WiFi board utilizes the ESP8266 WiFi enabled processor, and puts it onto an Arduino Uno board footprint. It provides a way to work with the ESP8266 in a familiar setup and does not require a breadboard in order to make interconnections since it has the typical on-board female headers. It will also work with some Uno shields that have compatible I/O pin-outs.
Arduino Joystick Shield
- Compatibility: Designed for use with Arduino boards.
- Joystick: Features a two-axis joystick for precise control in both X and Y directions.
- Buttons: Equipped with multiple push buttons for additional input options.
- Shield Form Factor: Designed to be easily mounted onto Arduino boards, providing a convenient and compact form factor.
Arduino Shield – Nano CNC Machine V4 Board
This board is widely used for driver expansion board of engraving machines. There are a total 3 3-way slots for stepper motor driver modules (Model A4988 or Drv8825 - It sold separately at our store), and it can drive 3-way stepper motors each up to 2A. Each way stepper motor has two I/O ports and it means 6 I/O ports can manage 3 stepper motors. It is very convenient to operate.
NRF24L01 Wireless Module Adapter Board
This 5V-3.3V VCC Adapter Board for NRF24L01 Wireless Module enables you to use NRF24L01-type transceivers on 5V systems like Arduino.
It regulates the 5V input to 1.9~3.6V DC and incorporates bypass capacitors for reliable operation. The NRF24L01 utilizes the Enhanced ShockBurst (ESB) protocol to support two-way data packet communication with packet buffering, packet acknowledgment, and automatic retransmission of lost packets.
Reviews
There are no reviews yet.